In order to avoid any damage to the thermowell during operation due to mechanical loads, a wake frequency calculation per ASME PTC 19.3 TW-2016 is recommended for critical process conditions. In case of a calculation with negative results, the only constructive solution so far was to shorten the thermowell stem or to increase the root and tip diameter, accepting a longer response time of the thermometer. The only other alternative up to now was to use a support collar to stabilise the thermowell stem inside the flange nozzle. This variant required an on-site machining of the collar to assure an interference fit in flange nozzles. The ScrutonWell® design reduces the amplitude of oscillation by more than 90 % 1) and allows an easy and fast installation of the thermowell without support collar, and thus without expensive and time-consuming rework on site. The WIKA ScrutonWell® design has been tested and approved by the independent laboratories TÜV NEL (Glasgow) and the Institute for Mechanics and Fluid Dynamics (Technical University of Freiberg). The ScrutonWell® design can be used for all kind of solid-machined thermowells with flange connection, in Vanstone design or for weld-in or threaded process connection. This helical design has been used successfully for decades in a wide variety of industrial applications to effectively suppress vortex-induced vibration excitation. Special features - The damping of vibrational excitation by helical strakes is a recognised state of the art in a wide variety of industrial applications - Easier and more cost-effective installation of the thermowell without any machining of the collar or nozzle compared to the conventional support of the thermowell with support collar - Optimised root design for improved bending strength

Resistance thermometers of this series are used for the measurement of liquid and gaseous media at low and medium pressures. The resistance thermometer is screwed directly into the process. The electrical connection is made via connection terminals in the connection head (splash-proof). The measuring inserts are available in two variants, depending upon the application. There is a choice between versions with a replaceable, spring-loaded miniature measuring insert and versions with a non-replaceable measuring resistor built directly into the thermowell tip. Insertion length, process connection and sensor can each be selected for the respective application. Special features - Sensor ranges from -196 ... +500 °C [-320 ... +932 °F] - Compact design - Universal application - Direct installation into the process - Explosion-protected versions are available for many approval types

The Vortex TLD Diverter is designed for use in gravity flow applications handling abrasive materials such as coal and frac sand. Material from one source can be diverted to either of two or three destinations. The TLD Diverter offers replaceable wear liners for added abrasion resistance and removable access panels for internal inspection, cleaning or maintenance.

For almost 30 years, Trios Luchttechniek has been the specialist in the design, installation, and maintenance of industrial dust extraction and exhaust systems. We provide complete solutions: from advice and commissioning to service, measurements, and high-quality products such as filters, piping, and fans. Our skilled technicians take care of the installation of new systems and the maintenance of existing installations. In addition, we carry out measurements and supply high-quality products such as filters, industrial hoses, piping, fans, and spare parts. For extra security, we also offer service and maintenance on a contract basis, so that your systems continue to function optimally. As a certified company (VCA* 2017/6.0), we meet the highest standards in terms of quality, safety, health, and the environment. We draw up a health, safety, and environmental plan for each project, and our employees are personally VCA/VOL certified, which guarantees professional and safe working practices. With Trios Luchttechniek, you are choosing expertise, reliability, and complete service in industrial air technology.

Van Beek’s open and closed trough screw conveyors are easy to clean via the hinged or bolted trough covers. Efficient, hygienic and quick cleaning and Cleaning In Place (CIP): everything’s possible with our trough screw conveyors. That’s because they can be fitted with bolt-on lids, hinged lids and quick-release fasteners. Safety switches on the trough lids ensure that your employees can inspect and/or clean the trough screw conveyors free from any risk. Optionally, the cleaning fluid (CIP lines) drain can be fitted with a hygienic shut-off valve, thereby removing the possibility of ‘dead product zones’. The (animal) foodstuffs industry makes extensive use of closed trough screw conveyors. Granulates, powders and granules can be transported hygienically and dust-free using closed trough screw conveyors. For example, when transporting foodstuffs horizontally to a mixer. Trough screw conveyors are also often used in the chemical, pharmaceutical and plastics industries. Due to the closed system, taste, temperature level and moisture are retained. Another advantage of a closed system is that not only is there no product loss from the inside to the outside, but also no foreign products can enter from outside.

The Vortex Titan Series TSG Gate is designed to meet the most demanding applications when handling heavy-duty abrasive materials such as sand, gravel, coal, and whole grains. The TSG Gate handles dry material in gravity flow applications where positive material shut-off and dust tight sealing is required. This slide gate is available in a wide variety of configurations with rectangular sizes and customer specific hole patterns.

TUBE CHAIN CONVEYORS. MADE BY SCHRAGE IN FRIEDEBURG, GERMANY. BULK MATERIAL EQUIPMENT MADE IN GERMANY – MOBILE AND STATIONARY INSTALLATIONS How can you make sure that your bulk materials get from point A to point B safely and reliably? That’s right! With tube chain conveyors made by Friedeburg-based Schrage. Whether stationary or mobile, Schrage conveying systems can be customized to meet your specific needs, and accordingly can tackle an extremely wide variety of tasks in virtually any industry. Our focus is not only on maximum efficiency, but also on ensuring that our systems are easy to operate and self-cleaning. which is why we use the best possible materials and bulk material technology out there. Moreover, an enclosed design guarantees that even dusty and toxic bulk materials will get to their destination without posing any risks to safety. Are you interested in finding out how a tube chain conveyor can help you take care of your needs more effectively? That’s why we’re here! Our conveying technology experts will be more than happy to assist you. www.schrage.de

Tube conveyors are closed screw conveyor systems that have a long service life. They require little maintenance, and are a relatively cheap solution for transporting (very fine) powders, granules and granulates. Our EasyClean tube conveyors with a removable screw make cleaning and inspection very easy and fast. Sectors that have been using tube conveyors successfully for years include the (pet) food industry, and companies in the chemical and recycling sector. In these sectors, tube conveyors (dosing screws) are used, for example, for dosed feeding of raw materials for paints or for loading sugar. A tube conveyor can load powders, granules and granulate up to an angle of 90°. This is ideal in working situations where you want to bridge a height in a limited space using closed screw conveyor systems.

Our stainless steel turntables can be delivered with a width of 1000, 1200 or 1500mm. The turntable has side-guides and the drive is equipped with a slow-start cooling fan. The turntable is supplied with an isolating switch and thermal protection.

TYR rotary lobe blowers are our modern high-performance vacuum and overpressure generators. With the TYR family, we have set new standards in terms of efficiency and noise level. They are available in a vacuum or an overpressure version. A conversion is possible at any time. TYR rotary lobe blowers provide constant differential pressure. Therefore, they are the perfect choice for applications such as waste water treatment, pneumatic conveying or fish farming. The various sizes of TYR blowers allow for the optimum configuration to match every process. The quiet and robust vacuum and overpressure generators - Robust construction - Flow-optimized blower stages - Reduced noise level - V-belt drive - Various design options

The fine impact mills belonging to the Ultraplex® UPZ product line are used for grinding finenesses in the range 50 µm to 5 mm. A wide range of grinding elements is available, making it possible to operate the UPZ as a pin mill if required.